Comparison of three common pre-treatment methods for the determination of lead contents by GFAAS in Chinese health-care wines.

Sample pre-treatment plays an important role in sample analysis, which directly affects the accuracy and reliability of the results. In this work we studied the influence of three common sample pre-treatment methods (direct injection, microwave digestion and wet digestion) on the determination of lead (Pb) content of Chinese health-care wines by graphite furnace atomic absorption spectrometry (GFAAS). Six different brands of Chinese health wines were selected for the research. After each Chinese health-care wine was digested by three digestion methods, GFAAS was used to detect the Pb content of the samples. For the selected six different health-care wines, the results showed that the Pb content obtained by GFAAS with different pre-treatment methods were different. Microwave digestion had the best recovery, and was proposed to be applied to the pre-treatment of many kinds of health-care wines, while the direct injection method might be suitable only for health-care wine with lesser amounts of ingredients such as sugar. In the practical work, due to the complexity of the base composition of Chinese health-care wines, currently there is no relevant standard analysis method for the pre-treatment of Chinese health wines. According to the accuracies of the three chosen common pre-treatment methods, it was proposed that microwave digestion might be more suitable as a standard digestion method for the determination of Pb in Chinese health-care wines. This work could provide theoretical support for the further establishment of a standard analytical method for the determination of lead and other (heavy) metal elements in Chinese health wines by GFAAS and other methods.

Assay in serum of exchangeable copper and total copper using inductively coupled plasma mass spectrometry (ICP-MS): development, optimisation and evaluation of a routine procedure.

The assay in serum of non-caeruloplasmin copper, as exchangeable copper after complexation with EDTA (ExCu) and total copper has been evaluated and compared in patients with varying c-reactive protein(CRP). Measurement of ExCu and total copper, range 0.2-47.2 µmol/L, was developed using ICP-MS. The chelating agents EDTA and TEPA were compared over 0.0-10 g/L after incubation with serum for 60 mins followed by ultrafiltration with Amicon 10 kDa filter. The assay for ExCu was optimised with EDTA 3 g/L (8.1 mmol/L) maintained at pH 7.0-8.0 before ultrafiltration. TEPA was not as selective in chelation of copper. Patients n = 82 were studied in relation to changes in inflammatory marker CRP and a group of patients n = 37 with normal CRP. The ExCu assay gave excellent recoveries (94-102 % but poor recovery for free uncomplexed copper), good repeatability, limit of quantitation 0.19 µmol/l with a provisional reference range 0.48 to 1.63 µmol/L (n = 37 patients). The range for relative exchangeable copper (exchangeable copper divided by total serum copper) was 2.49 to 9.96 %. ExCu was elevated in conditions with increased CRP greater than 100 mg/L suggesting an effect of inflammation on the free copper fraction. A reliable and reproducible assay for ExCu and total copper has been developed. The upregulated inflammatory state increases the ExCu suggesting excess free copper.

Simultaneous multielement analysis by ICP-MS with simple whole blood sample dilution and its application to uremic patients undergoing long-term hemodialysis.

Few studies were reported on trace elements' alterations in uremic patients undergoing long-term (>24 months) hemodialysis (HD), especially by using the whole blood as the biological fluid for the measuring purpose. Our objective was to develop an improved micro-sampling inductively coupled plasma-mass spectrometry (ICP-MS) method to determine the levels of Ca, Mg, Cu, Zn, Fe, Mn, Se and Pb in uremic patients receiving long-term HD. A ICP-MS method with a modified whole blood sample preparation procedure with small volumes was established and applied for the simultaneous quantification of the various elements in uremic patients undergoing long-term HD. 124 eligible uremic patients receiving long-term HD (75 males and 49 females) and 77 healthy subjects (54 males and 23 females) were recruited and Ca, Mg, Cu, Zn, Fe, Mn, Se and Pb levels were further determined. Our results revealed that uremic patients with HD had significantly higher blood levels of Ca, Mg, Zn and Pb and lower Cu, Fe, Se and Mn concentrations than healthy controls. In conclusion, a reproducible and reliable ICP-MS method using minimal whole blood sample volume (50 µL) with a simple dilution-based preparation procedure was successfully improved, validated and applied. Uremic patients undergoing long-term HD might be at increased risk of some essential trace elements deficiency (especially for Cu, Fe and Se) or toxic trace element excess (Pb) in respect to healthy subjects. Monitoring of blood levels and supplementation of some trace elements may be indicated in uremic patients undergoing long-term HD.

Direct analysis of calcium in liquid infant formula via laser-induced breakdown spectroscopy (LIBS).

The present work illustrates the potential of laser-induced breakdown spectroscopy (LIBS) for the direct analysis of liquid food products. The aim of the experiment was to predict calcium content in ready-to-feed infant formula. The analysis was performed by a LIBS system coupled to a liquid sample chamber with a rotatory wheel that presents the liquid to the laser beam as a thin film. Multivariate analysis with partial least squares regression (PLSR) was performed to correlate LIBS spectral data to reference calcium contents. The obtained PLSR model exhibited a good fit and linearity, as indicated by the coefficients of determination for calibration (Rc2) and cross-validation (Rcv2), with values of 0.96 and 0.89, respectively. The robustness of the calibration model was assessed by external validation showing a root-mean-square error of prediction of 6.45 mg 100 mL-1. These results demonstrated the potential of LIBS for real-time analysis of liquid food products.

Characterization the level of a new low-cost adsorbent material prepared from date palm kernel pits via DP-LIBS and ICP-OES spectroscopic techniques.

We successfully developed a fast detection system based on orthogonal dual-pulsed laser-induced breakdown spectroscopy (DP-LIBS) to characterize the level of a new low-cost adsorbent material prepared from date palm kernel pits. The activated carbon (AC) was produced from different heated and chemically treated date palm kernel pit samples to be used as adsorbent material for the removal of some pollutants from wastewater. The quantitative, as well as qualitative analysis, was performed using the DP-LIBS analytical technique. Hence, the valuable elements like the carbon present in the date palm kernel pits was perfectly recognized. The registered spectra of the sample cover the spectral lines of carbon. The quantitative analysis of carbon, carried out in different samples of date palm kernel pits, using DP-LIBS revealed that the estimated limit of detection of carbon in these samples is about 225.19 mg/L. The precision of DP-LIBS data for determining the concentration of activated carbon element present in the date palm kernel pits was validated via the inductively coupled plasma-optical emission spectrometry (ICP-OES) as a standard technique.

Inductively coupled plasma mass spectrometry assay for quantification of free infliximab in serum.

TNF antagonists such as infliximab are effective for the treatment of several inflammatory and autoimmune diseases. Recent clinical studies have advocated the importance of measuring trough infliximab levels to guide treatment decisions. We have developed a novel assay for measuring serum free infliximab levels using inductively coupled plasma-mass spectrometry (ICP-MS). The method involves the incubation of patient serum in wells coated with recombinant TNF, followed by detection with lanthanide-labeled monoclonal anti-human IgG1 and ICP-MS analysis. Full method validation was performed and results for clinical samples tested with the new method were compared with those obtained from a capture ELISA and a cell-based assay. Validation of the ICP-MS assay revealed a lower limit of detection of 0.4 µg/mL in serum. The linear range of quantitation was 1-50 µg/mL. The within-run and between-run precision had a coefficient of variation (CV) of <10%, and the accuracy of the assay had a CV of <15%. In serum samples, the ICP-MS method was devoid of analytical interferences by high levels of hemoglobin, bilirubin and triglycerides. Serum sample results from 123 drug-naïve donors revealed a test cutoff at 0.5 µg/mL. Test results from clinical samples obtained by the ICP-MS method showed strong correlation with both the ELISA and cell-based assay. The ICP-MS methodology presented in this study is a robust method for measuring TNF antagonist serum levels, which makes it well suited for therapeutic drug monitoring in the clinical laboratory.

Fast and direct analysis of Cr, Cd and Pb in brown sugar by GF AAS.

A simple and fast analytical method for the determination of Cr, Pb and Cd in brown sugar by GF AAS using slurry sampling was developed and in house validated for the first time. Analytical curves were prepared by external standardization for Cr, and by matrix simulation for Pb and Cd and they were linear. Low limits of quantification for Cr (32.8 ng g-1), Pb (49.3 ng g-1) and Cd (4.5 ng g-1) were found. Repeatability and intermediate precision estimates (<10% and <15%, respectively) and recovery rates (95-103%) demonstrated a good precision and accuracy. The levels in brown sugar samples ranged from <32.8 to 160 ng g-1 for Cr, from <49.3 to 211.0 ng g-1 for Pb and from <4.5 to 7.0 ng g-1 for Cd and they may be assigned to anthropogenic activities and the adoption of inadequate practices of production and processing.

Microwave-Induced Plasma Optical Emission Spectrometry (MIP OES) and Standard Dilution Analysis to Determine Trace Elements in Pharmaceutical Samples.

In this work, we evaluate the application of microwave-induced plasma optical emission spectrometry (MIP OES) to determine of Al, Cr, Co, Cu, Fe, Mn, Ni and Zn in children's cough syrup, eye drops, and oral antiseptic using standard dilution analysis (SDA). The SDA method is simple, with only two calibration solutions prepared per sample. The first solution (S1), composed of 50% sample +50% of a standard solution, is introduced into the plasma and the analytical signals are monitored in a time-resolved fashion. Then, the second solution (S2), composed of 50% sample +50% blank, is poured into the vial containing S1. As the solutions mix, the analytical signals gradually drop to a stable baseline. The calibration curve is computed by plotting the ratio of the analyte signal (SA) over the internal standard signal (which is also part of S1) (SIS) on the y-axis, versus the inverse of the IS concentration on the x-axis (i.e., SA/SIS versus 1/CIS). In this study, SDA results were compared with values obtained with the traditional methods of external calibration (EC), internal standardization (IS), and standard additions (SA) in MIP OES determinations. The precision (represented as percent RSD) for SDA showed values in the range of 2.50-8.00% for all samples, while conventional calibration methods showed RSDs in the range of 6.40-32.50% for EC, 8.30-21.80% for IS, and 5.20-17.40% for SA. The LODs calculated for SDA are below the maximum limits allowed by the major pharmaceutical regulatory agencies, and presents superior precision and accuracy compared to the traditional calibration methods. Considering its simplicity and efficiency, SDA is an important new tool for accurate analyses of pharmaceuticals.

Whole blood selenium determination by inductively coupled plasma mass spectrometry.

OBJECTIVE: To develop a sensitive method for accurately measuring whole blood selenium and determining an appropriate reference interval for the local Cleveland population. DESIGN AND METHODS: The assay was developed and validated on an inductively coupled plasma mass spectrometry (ICP-MS) with a collision cell. Whole blood trace element free EDTA tubes were used to collect samples for the reference interval study (n=50). Samples were collected after at least 8h fast from healthy adults (76% females) with ages between 19 and 64yr. Whole blood aliquots (1mL) in acid washed cryogenic vials were stored at -70°C until analysis. RESULTS: The method passed the matrix effect, interference (except for Gd), and carryover tests. The method had a linear range of 0.2-7.1µmol/L with accuracies of 87.1-118.1%. The total assay imprecision (CV) was <2.5% across the concentration levels tested. Comparison to another ICP-MS assay offered by an independent clinical lab yielded a Deming regression with a slope of 0.98, an intercept of 0.1µmol/L, a standard error of estimate of 0.1µmol/L, a correlation coefficient of 0.9846, and an average difference of 0.8%. The whole blood Se reference interval using a transformed parametric method was 2.2-3.5µmol/L. CONCLUSIONS: This whole blood Se ICP-MS methodology is sensitive and acceptable for patient testing.

High Precision Zinc Stable Isotope Measurement of Certified Biological Reference Materials Using the Double Spike Technique and Multiple Collector-ICP-MS.

Biological reference materials with well-characterised stable isotope compositions are lacking in the field of 'isotope biochemistry', which seeks to understand bodily processes that rely on essential metals by determining metal stable isotope ratios. Here, we present Zn stable isotope data for six biological reference materials with certified trace metal concentrations: fish muscle, bovine muscle, pig kidney, human hair, human blood serum and human urine. Replicate analyses of multiple aliquots of each material achieved reproducibilities (2sd) of 0.04-0.13‰ for δ66/64Zn (which denotes the deviation of the 66Zn/64Zn ratio of a sample from a pure Zn reference material in parts per 1000). This implies only very minor isotopic heterogeneities within the samples, rendering them suitable as quality control materials for Zn isotope analyses. This endorsement is reinforced by (i) the close agreement of our Zn isotope data for two of the samples (bovine muscle and human blood serum) to previously published results for different batches of the same material and (ii) the similarity of the isotopic data for the samples (δ66/64Zn ≈ -0.8 to 0.0‰) to previously published Zn isotope results for similar biological materials. Further tests revealed that the applied Zn separation procedure is sufficiently effective to enable accurate data acquisition even at low mass resolving power (M/ΔM ≈ 400), as measurements and analyses conducted at much higher mass resolution (M/ΔM ≈ 8500) delivered essentially identical results.

On the use of certified reference materials for assuring the quality of results for the determination of mercury in environmental samples.

This work focused on the development and validation of methodologies for the accurate determination of mercury in environmental samples and its further application for the preparation and certification of new reference materials (RMs). Two certified RMs ERM-CC580 (inorganic matrix) and ERM-CE464 (organic matrix) were used for the evaluation of digestion conditions assuring the quantitative recovery of mercury. These conditions were then used for the digestion of new candidates for the environmental RMs: bottom sediment (M_2 BotSed), herring tissue (M_3 HerTis), cormorant tissue (M_4 CormTis), and codfish muscle (M_5 CodTis). Cold vapor atomic absorption spectrometry (CV AAS) and inductively coupled plasma mass spectrometry (ICP MS) were used for the measurement of mercury concentration in all RMs. In order to validate and assure the accuracy of results, isotope dilution mass spectrometry (IDMS) was applied as a primary method of measurement, assuring the traceability of obtained values to the SI units: the mole, the kilogram, and the second. Results obtained by IDMS using n(200Hg)/n(202Hg) ratio, with estimated combined uncertainty, were as follows: (916 ± 41)/[4.5 %] ng g-1 (M_2 BotSed), (236 ± 14)/[5.9 %] ng g-1 (M_3 HerTis), (2252 ± 54)/[2.4 %] ng g-1 (M_4 CormTis), and (303 ± 15)/[4.9 %] ng g-1 (M_CodTis), respectively. Different types of detection techniques and quantification (external calibration, standard addition, isotope dilution) were applied in order to improve the quality of the analytical results. The good agreement (within less than 2.5 %) between obtained results and those derived from the Inter-laboratory Comparison, executed by the Institute of Nuclear Chemistry and Technology (Warsaw, Poland) on the same sample matrices, further validated the analytical procedures developed in this study, as well as the concentration of mercury in all four new RMs. Although the developed protocol enabling the metrological certification of the reference value was exemplified by the determination of mercury in environmental samples, it could be considered as valid for any certification procedure required whenever new certified RMs are introduced.

Measurement of titanium in hip-replacement patients by inductively coupled plasma optical emission spectroscopy.

Background Patients with metal-on-metal hip replacements require testing for cobalt and chromium. There may also be a need to test for titanium, which is used in the construction of the femoral stem in total hip replacements. It is not possible to use quadrupole inductively coupled plasma mass spectrometry due to interferences. Methods Titanium was measured using inductively coupled plasma optical emission spectroscopy using the emission line at 336.1 nm and Y (internal standard) at 371.0 nm. Internal quality control materials were prepared for blood and serum and concentrations assigned using a sector field-inductively coupled plasma mass spectrometer. A candidate whole blood certified reference material was also evaluated. Results The method had detection and quantitation limits of 0.6 and 1.9 µg/L, respectively. The respective bias (%) and measurement uncertainty ( U) (k = 2) were 3.3% and 2.0 µg/L (serum) and - 1.0% and 1.4 µg/L (whole blood). The respective repeatability and intermediate precision (%) were 5.1% and 10.9% (serum) and 2.4% and 8.6% (whole blood). The concentration of titanium was determined in patients' samples, serum (median = 2.4 µg/L, n = 897) and whole blood (median = 2.4 µg/L, n = 189). Serum is recommended for monitoring titanium in patients, since the concentration is higher than in whole blood and the matrix less problematic. In hip fluid samples, the concentrations were much higher (mean 58.5 µg/L, median 5.1 µg/L, n = 83). Conclusions A method based on inductively coupled plasma optical emission spectroscopy was developed and validated for measuring titanium in clinical samples.

Determination of Phosphorus and Potassium in Commercial Inorganic Fertilizers by Inductively Coupled Plasma-Optical Emission Spectrometry: Single-Laboratory Validation, First Action 2015.18.

A previously validated method for the determination of both citrate-EDTA-soluble P and K and acid-soluble P and K in commercial inorganic fertilizers by inductively coupled plasma-optical emission spectrometry was submitted to the expert review panel (ERP) for fertilizers for consideration of First Action Official Method(SM) status. The ERP evaluated the single-laboratory validation results and recommended the method for First Action Official Method status and provided recommendations for achieving Final Action. Validation materials ranging from 4.4 to 52.4% P2O5 (1.7-22.7% P) and 3-62% K2O (2.5-51.1% K) were used for the validation. Recoveries from validation materials for citrate-soluble P and K ranged from 99.3 to 124.9% P and from 98.4 to 100.7% K. Recoveries from validation materials for acid-soluble "total" P and K ranged from 95.53 to 99.40% P and from 98.36 to 107.28% K. Values of r for citrate-soluble P and K, expressed as RSD, ranged from 0.28 to 1.30% for P and from 0.41 to 1.52% for K. Values of r for total P and K, expressed as RSD, ranged from 0.71 to 1.13% for P and from 0.39 to 1.18% for K. Based on the validation data, the ERP recommended the method (with alternatives for the citrate-soluble and the acid-soluble extractions) for First Action Official Method status and provided recommendations for achieving Final Action status.

Simple analysis of total mercury and methylmercury in seafood using heating vaporization atomic absorption spectrometry.

This study aimed to develop a simpler method for determining total mercury (T-Hg) and methylmercury (MeHg) in biological samples by using methyl isobutyl ketone (MIBK) in the degreasing step. The fat in the samples was extracted by MIBK to the upper phase. T-Hg transferred into the water phase. This was followed by the extraction of MeHg from the water phase using HBr, CuCl2 and toluene. The MeHg fraction was reverse-extracted into L-cysteine-sodium acetate solution from toluene. The concentrations of T-Hg and MeHg were determined by heating vaporization atomic absorption spectrometry. Certified reference materials for T-Hg and MeHg in hair and fish were accurately measured using this method. This method was then applied to determine T-Hg and MeHg concentrations in the muscle, liver and gonads of seafood for the risk assessment of MeHg exposure. The mean T-Hg and MeHg concentrations in squid eggs were 0.023 and 0.022 µg/g, and in squid nidamental glands 0.052 and 0.049 µg/g, respectively. The MeHg/T-Hg ratios in the eggs and nidamental glands of squid were 94.4% and 96.5%, respectively. The mean T-Hg and MeHg concentrations in the gonads of sea urchins were 0.043 and 0.001 µg/g, respectively, with a MeHg/T-Hg ratio of 3.5%. We developed an efficient analytical method for T-Hg and MeHg using MIBK in the degreasing step. The new information on MeHg concentration and MeHg/T-Hg ratios in the egg or nidamental glands of squid and gonads of sea urchin will also be useful for risk assessment of mercury in seafood.

Determination of lead, cadmium and nickel in hennas and other hair dyes sold in Turkey.

The concentrations of lead, nickel and cadmium in various hennas and synthetic hair dyes were determined by high-resolution continuum source graphite furnace atomic absorption spectrometry (HR-CS GFAAS). For this purpose, 1 g of sample was digested using 4 mL of hydrogen peroxide (30%) and 8 mL of nitric acid (65%). The digests were diluted to 15 mL and the analytes were determined by HR-CS GFAAS. All determinations of Pb and Cd were performed using NH4H2PO4 as a modifier. The analytes in hair certified reference materials (CRMs) were found within the uncertainty limits of the certified values. In addition, the analyte concentrations added to hair dye were recovered between 95 and 110%. The limits of detection of the method were 48.90, 3.90 and 12.15 ng g(-1) for Pb, Cd and Ni, respectively and the characteristic concentrations were 8.70, 1.42 and 6.30 ng g(-1), respectively. Finally, the concentrations of the three analytes in various synthetic hair dyes with different brands, shades and formulae as well as in two henna varieties were determined using aqueous standards for calibration. The concentrations of Pb, Cd and Ni in hair dyes were in the ranges of LOD-0.56 µg g(-1), LOD-0.011 ng g(-1) and 0.030-0.37 µg g(-1), respectively, whereas those in the two hennas were 0.60-0.93 µg g(-1), 0.033-0.065 ng g(-1) and 0.49-1.06 µg g(-1), respectively.

Magnetic effervescent tablet-assisted ionic liquid dispersive liquid-liquid microextraction of selenium for speciation in foods and beverages.

A novel, simple and rapid method based on magnetic effervescent tablet-assisted ionic liquid dispersive liquid-liquid microextraction (MEA-IL-DLLME) followed by graphite furnace atomic absorption spectrometry (GFAAS) determination was established for the speciation of selenium in various food and beverage samples. In the procedure, a special magnetic effervescent tablet containing CO2 sources (sodium carbonate and sodium dihydrogenphosphate), ionic liquids and Fe3O4 magnetic nanoparticles (MNPs) was used to combine extractant dispersion and magnetic recovery procedures into a single step. The parameters influencing the microextraction efficiency, such as pH of the sample solution, volume of ionic liquid, amount of MNPs, concentration of the chelating agent, salt effect and matrix effect were investigated and optimised. Under the optimised conditions, the limits of detection (LODs) for Se(IV) were 0.021 µg l(-)(1) and the linear dynamic range was 0.05-5.0 µg l(-)(1). The relative standard deviation for seven replicate measurements of 1.0 µg l(-)(1) of Se(IV) was 2.9%. The accuracy of the developed method was evaluated by analysis of the standard reference materials (GBW10016 tea, GBW10017 milk powder, GBW10043 Liaoning rice, GBW10046 Henan wheat, GBW10048 celery). The proposed method was successfully applied to food and beverage samples including black tea, milk powder, mushroom, soybean, bamboo shoots, energy drink, bottled water, carbonated drink and mineral water for the speciation of Se(IV) and Se(VI) with satisfactory relative recoveries (92.0-108.1%).

Cobalt internal standard for Ni to assist the simultaneous determination of Mo and Ni in plant materials by high-resolution continuum source graphite furnace atomic absorption spectrometry employing direct solid sample analysis.

A new method is proposed for the simultaneous determination of Mo and Ni in plant materials by high-resolution continuum source graphite furnace atomic absorption spectrometry (HR-CS GFAAS), employing direct solid sample analysis (DSS) and internal standardization (IS). Cobalt was used as internal standard to minimize matrix effects during Ni determinations, enabling the use of aqueous standards for calibration. Correlation coefficients for the calibration curves were typically better than 0.9937. The performance of the method was checked by analysis of six plant certified reference materials, and the results for Mo and Ni were in agreement with the certified values (95% confidence level, t-test). Analysis was made of different types of plant materials used as renewable sources of energy, including sugarcane leaves, banana tree fiber, soybean straw, coffee pods, orange bagasse, peanut hulls, and sugarcane bagasse. The concentrations found for Mo and Ni ranged from 0.08 to 0.63 ng mg(-1) and from 0.41 to 6.92 ng mg(-1), respectively. Precision (RSD) varied from 2.1% to 11% for Mo and from 3.7% to 10% for Ni. Limits of quantification of 0.055 and 0.074 ng were obtained for Mo and Ni, respectively.

Standard dilution analysis of beverages by microwave-induced plasma optical emission spectrometry.

In this work, standard dilution analysis (SDA) is combined with microwave-induced plasma optical emission spectrometry (MIP OES) to determine seven elements in coffee, green tea, energy drink, beer, whiskey and cachaça (Brazilian hard liquor). No sample preparation other than simple dilution in HNO3 1% v v(-1) is required. Due to relatively low plasma temperatures, matrix effects may compromise accuracies in MIP OES analyzes of complex samples. The method of standard additions (SA) offers enhanced accuracies, but is time-consuming and labor intensive. SDA offers a simpler, faster approach, with improved accuracies for complex matrices. In this work, SDA's efficiency is evaluated by spike experiments, and the results are compared to the traditional methods of external calibration (EC), internal standard (IS), and standard additions (SA). SDA is comparable to the traditional calibration methods, and it provides superior accuracies for applications involving ethanol-containing beverage samples. The SDA-MIP OES procedure is effective. Using only two calibration solutions, it may be easily automated for accurate and high sample throughput routine applications.

Propuesta de un procedimiento de validación de un método para la determinación de cinc sérico: cumplimiento de los requisitos de la ISO 17025 / Validation of an in-house method for the determination of zinc in serum: Meeting the requirements of ISO 17025

Objetivo. Elaborar un esquema de validación de una técnica analítica siguiendo los requisitos de la ISO 17025. Material y métodos. Teniendo en cuenta la ISO 17025, los parámetros verificados fueron: selectividad, modelo de calibración y linealidad, precisión, exactitud, incertidumbre de medida e interferencias analíticas. Resultados. El procedimiento desarrollado fue aplicado satisfactoriamente para cuantificar cinc en suero por espectrofotometría de absorción atómica. Conclusión. Finalmente, se ha demostrado que nuestro método cumple con los requisitos exigidos de selectividad, linealidad, exactitud y precisión, haciéndolo adecuado para el fin requerido (AU)

Objective. The aim of this report is to propose a scheme for validation of an analytical technique according to ISO 17025. Material and methods. According to ISO 17025, the fundamental parameters tested were: selectivity, calibration model, precision, accuracy, uncertainty of measurement, and analytical interference. Results. A protocol has been developed that has been applied successfully to quantify zinc in serum by atomic absorption spectrometry. Conclusion. It is demonstrated that our method is selective, linear, accurate, and precise, making it suitable for use in routine diagnostics (AU)

[Validation of an in-house method for the determination of zinc in serum: Meeting the requirements of ISO 17025]. / Propuesta de un procedimiento de validación de un método para la determinación de cinc sérico: cumplimiento de los requisitos de la ISO 17025.

OBJECTIVE: The aim of this report is to propose a scheme for validation of an analytical technique according to ISO 17025. MATERIAL AND METHODS: According to ISO 17025, the fundamental parameters tested were: selectivity, calibration model, precision, accuracy, uncertainty of measurement, and analytical interference. RESULTS: A protocol has been developed that has been applied successfully to quantify zinc in serum by atomic absorption spectrometry. CONCLUSION: It is demonstrated that our method is selective, linear, accurate, and precise, making it suitable for use in routine diagnostics.